Use the new LR 32 Guide Rail Connector to precisely align multiple LR 32 style rails for precision hole drilling in larger workpieces*. With longer rail options, you can accurately place shelf pins holes and European hardware based on the 32 mm system on taller case goods and cabinets.With the new LR 32 Guide Rail Connector, it is possible to drill closer to the end of the rail, maximizing the value of existing single guide rail setups.
This product is used to produce accurate spacing when joining two LR 32 guide rails. The guide rail connectors (482107) are required and must be purchased separately.
x
Used with edging plate to deflect chips into dust extraction hood.
When attached to the Festool OF 1010 Router, the Edge Guide allows you to rout perfectly parallel to the material edge, delivering precise dados, rabbets, flutes, grooves and ploughs. Attaches quickly and easily to the router using integrated thumbscrews and two steel rods included with the OF 1010. Optional chip guard enables ultra-efficient dust extraction, saving valuable cleanup time. Chip Guard (437307) sold separately.
Includes shaft and 3 scanning rollers. Attaches to angle arm to copy workpieces and patterns. Scanning roller follows contours and guides cutter.
Works with 1/4″ and 8 mm collets.
Copying ring, KR-D13.8mm (.543″), dia 11mm (.433″), OF1010
With two adjustable fences and integrated rule for routing grooves and slots on edges.
Used with copier scanning set to copy workpieces. Used with edging plate for trimming edges flush. Copier set and edging plate sold separately.
Extension table – extends support area for edge trimming. Small center bore eases edge and corner routing. Outrigger handle for additional support.
Festool FS Guide rails are available in eight different lengths from 32 inches to 197 inches (800 – 5000 mm), providing the right rail for every application. The integrated splinterguard aligns perfectly to your cut line, saving set up time and serving as protection against tear out, on cuts both with the grain and across. Guide rails can be easily connected using the accessory guide rail connectors for a rigid, secure and continuous connection. Guide rails make work easier by taking the tool to the work, and save time and money by eliminating laborious measurements, rework and wasted material. Connect rails using Festool Guide Rail Connectors to make limitless cuts.
The FS FS 2424/2-LR 32 Guide Rail (95 inches) was designed specifically for use with Festool Routers and the LR 32 Hole Drilling System to construct cabinets using the European frameless 32mm system for shelf pins and hardware. Also, use the LR 32 System for line boring, or setting shelf pins in panels up to any length. Festool FS Guide rails are available in eight different lengths from 32 inches to 197 inches (800 – 5000 mm), providing the right rail for every application. For cutting applications, the integrated splinterguard aligns perfectly to your cut line, saving set up time and serving as protection against tear out, on cuts both with the grain and across. Guide rails can be easily connected using the accessory guide rail connectors for a rigid, secure and continuous connection. Guide rails make work easier by taking the tool to the work, and save time and money by eliminating laborious measurements, rework and wasted material. Use the FS 2424/2-LR 32 Guide Rail (95 inches) with the Festool Plunge cut saw to cut material up to 89 inches. Connect rails using Festool Guide Rail Connectors to make limitless cuts.
Copying ring, KR-D10.8mm (.425″), dia 9mm (.354″), OF1010
With the LR 32 Hole Drilling System from Festool, you can precisely and efficiently build cabinets using the European frameless 32 mm system. Invaluable for placing cup hinges (35mm) or setting shelf pin holes (based on 32mm spacing) in casework, this portable line boring system allows you do in the field what has traditionally been a shop-only job, possible only with large stationary equipment. For use with the Festool OF 1010 and OF 1400 routers and guide rail system, the LR 32 System is supported by a 42in, 55in and a 95in rail (sold separately), to cover any size job. Includes: Guide plate, Centering mandrel, 2 edge stops, 2 linear stops, 2 clamps, Operating wrench, 35 mm carbide-tipped European hinge boring bit, 2 carbide-tipped 5 mm shelf pin bits (one for through holes and one for stopped pin holes).
For parallel alignment of LR 32 guide rail. Includes stop and sliding stop flag.
Replacement edge stop, post and sliding stop flag
Replacement Guide Stop for use with the OF 1010 Router and FS Guide Rail System. Maximize the versatility of your Festool Router and Guide Rail System! Use the Guide Stop to adapt the Festool OF 1010 Router for use with the FS Guide Rail System for perfectly guided, straight routing. The Guide Stop attaches quickly and easily using two rods included in the scope of delivery of the OF 1010 router.
Replacement sliding stop flag for edge stop used with LR 32 guide rail.
Orients router on its side for flush trimming operations.
Quick and precise adjustment when using router with guide stop or edging plate.
Includes Fine Adjustment for OF 1010 EQ Edge Guide.
Customize the solid base piece hole diameter with a plunge bit to meet your needs. Provides support across the entire surface of the router base. Ideal for working with smaller diameter bits especially for greater support on outside corners. Does not have the center bore.
The Trammel Unit for the Festool OF 1010 Router allows you to rout precise circles and decorative curves from 6-1/32 inches up to 29-7/8 inches in diameter. Anchored in the center with the included trammel point, and attaches simply and securely to the router using thumbscrews.
Auxiliary dust extraction hood for VS 600.
Clamping collet 1/4″, SZ-D6,35-OF1010
Clamping collet 8 mm, SZ-D8/OF1010
Copying ring, KR-D17mm (.669″), dia 15mm (.590″), OF1010
Copying ring, KR-D24mm (.944″), dia 21mm (.826″), OF1010
Copying ring, KR-D27mm (1.062″), dia 25mm (.984″), OF1010
Copying ring, KR-D30mm (1.181″), dia 27mm (1.062″), OF1010
40mm template guide, compatible with OF 1000 and OF 1010 routers. D=40mm, d=37mm
Guide plate, centering mandrel, linear stops and two edge stops for drilling.European 32 mm grid pattern holes in shelves and cabinets. Guide rail and bits sold separately.
Maximize the versatility of your Festool Router and Guide Rail System! Use the Guide Stop to adapt the Festool OF 1400 Router for use with the FS Guide Rail System for perfectly guided, straight routing. The OF 1400 Guide Stop features fine-adjustment controls, allowing you to precisely adjust the distance to cut in increments of 1/10mm. Also included with the Guide Stop is a support foot to levels the router to the surface of the guide rail, ensuring smooth, accurate results and increased stability. The Guide Stop attaches quickly and easily using two rods included in the scope of delivery of the OF 1400 router, and two knobs that double as handles for guiding the router along the guide rail.
Replacement.
Accessory base for use with small diameter edge-forming bits. Provides stability on outside corners by extending the base to the inside near the bit.
Oversized, heavy-duty base plate with integrated dust hood.
Copying ring, KR-D 40 mm (1.575″), OF 1400
Template Guide, 30 mm OD / 27 mm ID
Copying ring, KR-D 27mm (1.062″), OF 1400
Copying ring, KR-D 24 mm (.944″), OF 1400
With flange for VS 600 Jointing System.
Collet w/nut 3/8in, OF1400/2200, replaces 492142
When used with the Festool OF 1400 Router, the Parallel Edge Guide allows you to rout up against, or perfectly parallel to the material edge, delivering precise dados, flutes, grooves, ploughs, rabbets and profiles. Fine-adjustment control allows you to dial in the distance from the material edge in increments of 1/10mm for ultra-precise routing. Dust extraction hood enables ultra-efficient dust extraction, saving valuable cleanup time. The Edge Guide is constructed from durable cast aluminum, and includes fiber-reinforced plastic thumbscrews for easy adjustment and a long service life. Attaches quickly and easily using integrated thumbscrews and two steel rods included in the router’s scope of delivery.
Accepts industry standard two-piece threaded guide bushings.
Allows you to make cut outs over large areas by allowing the router to ride on the carriage. 23-1/2″ (600mm) traverse width.
Accessory base with dust channels for use with template guides.
Accessory base for use with small diameter edge-forming bits.
When used with the Festool OF 2200 Router, the Edge Guide allows you to rout up against, or perfectly parallel to the material edge, delivering precise dados, flutes, grooves, ploughs, rabbets and profiles. Fine-adjustment control allows you to dial in the distance from the edge in increments of 1/10mm for ultra-precise routing. The Edge Guide is constructed from durable cast aluminum, and includes fiber-reinforced plastic thumbscrews for easy adjustment and a long service life. Attaches quickly and easily using integrated thumbscrews and two steel rods included in the router’s scope of delivery.