Switch between drill functions in seconds with the FastFix interface, saving time and eliminating cost of dedicated, single purpose tools. The Festool FastFix Right Angle Chuck is the ultimate solution for close quarters hole or fastener placement. Drill or drive between studs, joists, cabinet or drawer spaces, or virtually any constrained space without switching over to a separate, dedicated tool. 1/4 inch hex drive with wire detent. Accepts Festool Centrotec or adjustable 1/2 inch chuck. Chuck rotates 360 degrees with 16 presets. Works with all existing and previous model Festool drills equipped with FastFix interface for toolless change of chucks: T+3, C12, TDK, TDD, CDD models.
x
Metal-sleeved chuck compatible with PDC, C and T Drills. Up to 1/2″ capacity. Ratcheting sleeve for increased retention.
Standard replacement chuck for the PDC Drill. Compatible with C and T Drills. Up to 1/2″ capacity. Ratcheting sleeve for increased retention.
Switch between drill functions in seconds with the FastFix interface, saving time and eliminating cost of dedicated, single purpose tools. The Festool FastFix Offset Chuck places bits flush to side, enabling close-quarters drilling and driving so you can place holes and fasteners near-perfectly adjacent to walls and into corners. Significantly faster and easier than the alternative of driving screws in tight spaces manually. Chuck rotates 360 degrees with 16 presets. Quick-release collar will not mar adjoining surfaces. Switch between drill functions in seconds with the FastFix interface, saving time and eliminating cost of dedicated, single use tools. Getting the job done right the first time eliminates waste of material and fasteners and saves valuable time. Works with all existing and previous model Festool drills equipped with FastFix interface for toolless change of chucks: T+3, C12, TDK, TDD, CDD models.
Switch between drill and driving functions in seconds with the FastFix interface, saving time and eliminating the cost of dedicated, single purpose tools. The Festool FastFix based Centrotec Chuck is extremely light weight and compact. This quick-release chuck provides two points of contact for Centrotec bits, allowing them to extend directly into the drill spindle so they serves as an extension of the motor, significantly improving controllability and torque. Reduce fatigue with the light weight Centrotec chuck and decrease necessary drilling/driving clearance with the compact design. Save time changing between drill and screw bits with the quick-change Centrotec System. Accessory Centrotec bits can be used both with the Centrotec chuck as well as non-Festool standard bit holders and chucks. Works with all existing and previous model Festool drills equipped with FastFix interface for toolless change of chucks: T+3, C12, TDK, TDD, CDD models.
Switch between drill and driving functions in seconds with the FastFix interface, saving time and eliminating the cost of dedicated, single purpose tools. The Festool FastFix Depth Stop Chuck is designed for consistent, precise depth setting regardless of material density. Integrated clutch maintains depth of fastener placement independent of torque setting. Green quick-out ring backs out screws without affecting depth setting. Great for jobs where you want to make sure the screws are perfectly flush every time, including dry wall, decks, and cabinets. Getting it right the first time eliminates waste of material and fasteners and saves valuable time. Works with all existing and previous model Festool drills equipped with FastFix interface for toolless change of chucks: T+3, C12, TDK, TDD, CDD models.
The SYS-1 Box Small Parts Organizer is an excellent solution for organization, storage, and transport of fasteners, hardware, and other small pieces (i.e. screws, washers, nails, nuts and bolts, etc.). An assortment of removable plastic container inserts come in 4 different color coded sizes. The Sys 1 Box makes it easy to maintain an organized workshop, or take small parts to a jobsite. Sold standard with most of our tools, Festool Systainers offer a rugged, flexible, and convenient means of storing, carrying, and combining tools and accessories. Designed to seamlessly connect to one another and to Festool Sortainers and CT Dust Extractors, the Systainer System makes it possible to configure highly mobile, job-specific kits, keeping you organized and working efficiently. Made of durable, robust, high quality ABS for long service-life. All Systainers share an identical footprint for easy stacking, storing, and transport. Centrally positioned, oversized handle makes it easy to carry heavy loads. Systainers are available in 5 different sizes, providing a solution for virtually every need.
2 3/8in Magnetic bit holder enables use of standard bits with Centrotec Chuck. The Centrotec shank is designed for use with the Festool Centrotec System, as well as with all standard or keyless chucks for no-slip performance. The Centrotec System was designed to provide a seamless transfer of force, eliminating bit slippage or marring of the drill bit. The weight of the drill is reduced by nearly ½ pound, and the length is reduced by nearly 1-1/2” with the Centrotec System. Most importantly, the Centrotec system offers a quicker and more secure means of bit change than any other quick-change chuck system. Thicker and stronger sidewall for longer life and use with impact or standard bits.
Faster re-charge for less down time. AIRSTREAM batteries with the new SCA 8 charger re-charge 60% faster than previous charging technology. And batteries equipped with AIRSTREAM design cool down 3X faster than non-equipped versions so the charging process can begin sooner getting you back to work faster.
Batteries for the toughest demands. Reduce downtime waiting for battery charging with the AIRSTREAM charging system with rapid battery cooling and charging. The new AIRSTREAM charging system – a combination of the AIRSTREAM SCA 8 rapid charger and the AIRSTREAM battery pack – reduces the cooling time of the battery and thus the entire charging process by up to 60 percent. This means that battery packs are ready to use again more quickly and you can continue working without interruptions. For professionals, this means unnecessary and expensive downtimes. The new AIRSTREAM Li-ion batteries fit all our current 18 V products.
Festool battery-powered tools free you from the constraints of electrical sockets and guarantee exceptional performance with a combination of a high-power battery pack and brushless EC-TEC motor. With the new super light compact battery pack now available for even easier and perfect handling.
The new Bluetooth® battery packs communicate with the Bluetooth® module on the mobile dust extractor and ensure that even a cordless tool starts the mobile dust extractor automatically when switched on. This allows you to now benefit from Festool’s entire dust-free system when working with Festool cordless products.
Centrotec Pozidrive Bit Long-shaft Centrotec Pozidrive bits for Pozidrive fasteners used on European hardware. Precision-milled shaft for near zero run-out. Also compatible with FastFix Keyless Chuck. Pozidrive 1–100 mm (2 pieces)
Centrotec Pozidrive Bit Long-shaft Centrotec Pozidrive bits for Pozidrive fasteners used on European hardware. Precision-milled shaft for near zero run-out. Also compatible with FastFix Keyless Chuck. Pozidrive 2–100 mm (2 pieces)
Centrotec Pozidrive Bit Long-shaft Centrotec Pozidrive bits for Pozidrive fasteners used on European hardware. Precision-milled shaft for near zero run-out. Also compatible with FastFix Keyless Chuck. Pozidrive 3–100 mm (2 pieces)
Centrotec Phillips Bit Long-shaft Centrotec Phillips bits. Precision-milled shaft for near zero run-out. Also compatible with FastFix Keyless Chuck. Phillips 1–100 mm (2 pieces)
Centrotec Phillips Bit Long-shaft Centrotec Phillips bits. Precision-milled shaft for near zero run-out. Also compatible with FastFix Keyless Chuck. Phillips 2–100 mm (2 pieces)
Centrotec Phillips Bit Long-shaft Centrotec Phillips bits. Precision-milled shaft for near zero run-out. Also compatible with FastFix Keyless Chuck. Phillips 3–100 mm (2 pieces)
Centrotec Torx Bit Long-shaft Centrotec Torx bits. Precision-milled shaft for near zero run-out. Also compatible with FastFix Keyless Chuck. Torx 15–100 mm (2 pieces)
Centrotec Torx Bit Long-shaft Centrotec Torx bits. Precision-milled shaft for near zero run-out. Also compatible with FastFix Keyless Chuck. Torx 20–100 mm (2 pieces)
Centrotec Torx Bit Long-shaft Centrotec Torx bits. Precision-milled shaft for near zero run-out. Also compatible with FastFix Keyless Chuck. Torx 25–100 mm (2 pieces)
Centrotec Torx Bit Long-shaft Centrotec Torx bits. Precision-milled shaft for near zero run-out. Also compatible with FastFix Keyless Chuck. Torx 30–100 mm (2 pieces)
6in Magnetic bit holder enables use of standard bits with Centrotec Chuck. The Centrotec shank is designed for use with the Festool Centrotec System, as well as with all standard or keyless chucks for no-slip performance. The Centrotec System was designed to provide a seamless transfer of force, eliminating bit slippage or marring of the drill bit. The weight of the drill is reduced by nearly ½ pound, and the length is reduced by nearly 1-1/2” with the Centrotec System. Most importantly, the Centrotec system offers a quicker and more secure means of bit change than any other quick-change chuck system.
This Centrotec compatible socket adapter accepts all 1/4″ sockets extending the capabilities of your Festool cordless drill.
This Centrotec compatible socket adapter accepts all 3/8″ sockets extending the capabilities of your Festool cordless drill.
Convert any non-Festool drill for use with the Centrotec System using this adapter which fits into a standard keyless chuck.
Drill bits made from high-alloy steel with center point and 2 cutters for drilling quick, clean holes. Two chamfers instead of pre-cutting blades for an extended service life. For drilling in all types of wood, glued solid wood, MDF and acrylic glass. Includes five bits: 3mm, 4mm, 5mm, 6mm and 8mm in diameter.
Set with Reusable Centrotec Shank provides a precise, compact, and durable solution for drilling wood, metal, and plastic. Precision-ground HSS steel stays sharp longer for precise hole drilling and a long service life. This set is based on a replaceable drill bit that fits securely into a reusable Centrotec shank for quick and efficient use with the Festool Centrotec Chuck System. The reusable Centrotec shank can also be used with all three-jaw chucks for no-slip performance. Though this set includes 2 additional replacement bits, 10-packs of HSS Spiral Drill replacement bits are also available. Set includes 3 bits, reusable Centrotec shank, set screw and allen wrench. The Festool Centrotec System is designed to deliver a better transfer of force between the drill and the bit, with no chance for bit slippage or marring of the drill bit. The Centrotec Chuck design enables a full 1/2 pound reduction in weight, and reduces the overall length, or clearance, by nearly 1-1/2 inches. The quick-change Centrotec system delivers a faster, more efficient means of changing bits and driver tips than any keyless chuck system, and virtually eliminates run out.
Pack of 10 replacement bits for use with reusable Centrotec shank (493421). Precision-ground HSS steel stays sharp longer for precise hole drilling and a long service life. Tip grind and flute design are ideal for drilling into wood, metal and plastics. Designed for use with reusable Centrotec shank, but can be used independently in any three-jawed keyless chuck.
HSS Spiral Drill Bits, 3.0mm
Pack of 10 replacement bits for use with reusable Centrotec shank (493422). Precision-ground HSS steel stays sharp longer for precise hole drilling and a long service life. Tip grind and flute design are ideal for drilling into wood, metal and plastics. Designed for use with reusable Centrotec shank, but can be used independently in any three-jawed keyless chuck.
HSS Spiral Drill Bits, 3.5mm
Pack of 10 replacement bits for use with reusable Centrotec shank (493423). Precision-ground HSS steel stays sharp longer for precise hole drilling and a long service life. Tip grind and flute design are ideal for drilling into wood, metal and plastics. Designed for use with reusable Centrotec shank, but can be used independently in any three-jawed keyless chuck.
HSS Spiral Drill Bits, 4.0mm
Pack of 10 replacement bits for use with reusable Centrotec shank (493424). Precision-ground HSS steel stays sharp longer for precise hole drilling and a long service life. Tip grind and flute design are ideal for drilling into wood, metal and plastics. Designed for use with reusable Centrotec shank, but can be used independently in any three-jawed keyless chuck.
HSS Spiral Drill Bits, 4.5mm
Pack of 10 replacement bits for use with reusable Centrotec shank (493425). Precision-ground HSS steel stays sharp longer for precise hole drilling and a long service life. Tip grind and flute design are ideal for drilling into wood, metal and plastics. Designed for use with reusable Centrotec shank, but can be used independently in any three-jawed keyless chuck.
HSS Spiral Drill Bits, 5.0mm
Pack of 10 replacement bits for use with reusable Centrotec shank (493426). Precision-ground HSS steel stays sharp longer for precise hole drilling and a long service life. Tip grind and flute design are ideal for drilling into wood, metal and plastics