Parallel Edge Guide enables guided, parallel cutting with the TS 55 Plunge Cut Saw. Can be used for parallel rip cutting with the TS saw, independent of the FS guide rails. Attaches to both sides of the saw for short side or broad side cuts. Rip capacity from the blade side up to 11 13/16in (300mm), and on the motor side up to 3 3/4in (95mm).
x
Cover Plate enhances dust extraction for the TS 55 Plunge Cut Saw by enclosing blade housing.
Festool FS Guide rails are available in eight different lengths from 32 inches to 197 inches (800 – 5000 mm), providing the right rail for every application. The integrated splinterguard aligns perfectly to your cut line, saving set up time and serving as protection against tear out, on cuts both with the grain and across. Guide rails can be easily connected using the accessory guide rail connectors for a rigid, secure and continuous connection. Guide rails make work easier by taking the tool to the work, and save time and money by eliminating laborious measurements, rework and wasted material. Connect rails using Festool Guide Rail Connectors to make limitless cuts.
Affixing to the rib, or guide on top of the Festool FS Guide Rail, the Limit Stop can be used to provide secure stop points for repetitive cutting and for routing with most Festool routers. With a seamless fit to the rear of the TS plunge cut saw’s sole plate, the Limit Stop also helps reduce the risk of kickbacks for plunge cut starts. Though Festool TS saws are packaged with a single Limit Stop a second stop is useful for pairing as a stop or start point. Includes one Limit Stop.
Replacement battery for use with all 15v or higher C-Series, T-series, BHC and PDC lithium ion cordless drills, SYSLITE worklamps, TSC cordless tracksaws, and CARVEX cordless jigsaws. Includes one 15v, 5.2Ah Li-ion battery.
Faster re-charge for less down time. AIRSTREAM batteries with the new SCA 8 charger re-charge 60% faster than previous charging technology. And batteries equipped with AIRSTREAM design cool down 3X faster than non-equipped versions so the charging process can begin sooner getting you back to work faster.
Batteries for the toughest demands. Reduce downtime waiting for battery charging with the AIRSTREAM charging system with rapid battery cooling and charging. The new AIRSTREAM charging system – a combination of the AIRSTREAM SCA 8 rapid charger and the AIRSTREAM battery pack – reduces the cooling time of the battery and thus the entire charging process by up to 60 percent. This means that battery packs are ready to use again more quickly and you can continue working without interruptions. For professionals, this means unnecessary and expensive downtimes. The new AIRSTREAM Li-ion batteries fit all our current 18 V products.
The new Bluetooth® battery packs communicate with the Bluetooth® module on the mobile dust extractor and ensure that even a cordless tool starts the mobile dust extractor automatically when switched on. This allows you to now benefit from Festool’s entire dust-free system when working with Festool cordless products.
Flush-mount Splinterguard protects material surface for both straight and bevel cuts. (5 pieces)
Festool saw blades are engineered and designed for cutting efficiency, long-life, and superior cutting results. The carbide tipped Universal General Purpose blade for the TS 55 Plunge Cut Saw is a clean-cutting general purpose blade for wood and soft plastics, and serves as a fine-rip cutting blade for glue-ready joints.This blade incorporates an offset tooth design known as ATB (Alternating Top Bevel), allowing the blade to cut alternately to the left and right, generating a more efficient and cleaner cut in all types of wood. This thin-kerfed blade design meets less resistance, for more efficient cutting, and produces less material waste. Laser cut expansion slots reduce vibration for faster, quieter cutting. An oversized 20mm arbor enables more secure fastening of the blade to the saw, further reducing vibration for more precise cutting.
Festool saw blades are engineered and designed for cutting efficiency, long-life, and superior cutting results. The carbide tipped Standard Ripping blade for the TS 55 Plunge Cut Saw is an excellent general purpose, clean-cutting blade for wood and soft plastics, and enables precision cutting for glue-ready joints. This blade incorporates an offset tooth design known as ATB (Alternating Top Bevel), allowing the blade to cut alternately to the left and right, generating a more efficient and cleaner cut in all types of wood. This thin-kerfed blade design meets less resistance, for more efficient cutting, and produces less material waste. Laser cut expansion slots reduce vibration for faster, quieter cutting. An oversized 20mm arbor enables more secure fastening of the blade to the saw, further reducing vibration for more precise cutting.
Festool saw blades are engineered and designed for cutting efficiency, long-life, and superior cutting results. The carbide tipped Solid Surface/Laminate blade for the TS 55 Plunge Cut Saw is a long-lasting , high cut quality blade for laminate flooring and solid surface countertop material. This blade incorporates a TC (Triple Chip), or trapezoidal flat tooth saw blade design, wherein the edges of alternating blade teeth are beveled on both sides. These beveled teeth alternate with the flat teeth when cutting into the material for smoother and more efficient cutting. This thin-kerfed blade design meets less resistance, for more efficient cutting, and produces less material waste. Laser cut expansion slots reduce vibration for faster, quieter cutting. An oversized 20mm arbor enables more secure fastening of the blade to the saw, further reducing vibration for more precise cutting.
Replaces product 495375.
Festool saw blades are engineered and designed for cutting efficiency, long-life, and superior cutting results. The carbide tipped Fine Tooth Cross-Cut Saw blade for the TS 55 Plunge Cut Saw is an excellent blade for smooth cross-cutting in veneered plywood, sheet goods, melamine, and hard and soft woods. This blade incorporates an offset tooth design known as ATB (Alternating Top Bevel), allowing the blade to cut alternately to the left and right, generating a more efficient and cleaner cut in all types of wood. This thin-kerfed blade design meets less resistance, for more efficient cutting, and produces less material waste. Laser cut expansion slots reduce vibration for faster, quieter cutting. An oversized 20mm arbor enables more secure fastening of the blade to the saw, further reducing vibration for more precise cutting.
